Jesel INS-32000 Mark 4/5, Gen 6 BB Chevy User Manual download pdf

APPLY A VERY THIN LAYER OF RTV SEALER TO THE

RECESSED AREA ON THE CAM ADAPTOR.

LUBRICATE AND INSTALL THE REAR THRUST WASHER

ON THE CAM SNOUT. APPLY RTV SEALANT TO THE

THREADS OF THE CAM ADAPTOR BOLTS AND BOLT

THE ADAPTOR TO THE CAMSHAFT.

TORQUE CAM ADAPTOR BOLTS TO 26-28 FT/LBS. A

SPANNER WRENCH (TOL-39260) IS AVAILABLE TO

ASSIST IN TIGHTENING THE BOLTS.

STEP 1

STEP 2

STEP 3

CAM BOLT IS

LH THREAD

KBD-32000

BIG-BLOCK

KIT SHOWN

SEE STEP 11 FOR AFTERMARKET BLOCKS

JESEL’S BIG-BLOCK CHEVY BELT DRIVE IS THE

MOST ACCURATE AND DURABLE CAMSHAFT

DRIVE SYSTEM AVAILABLE AND IS USED BY THE

COUNTRY’S TOP RACE TEAMS. A PATENTED HIGH

TORQUE BELT OPERATES WITHOUT LUBRICATION

AND SPINS WITH LESS FRICTION THAN CHAINS

OR GEAR DRIVE SYSTEMS. THE RUBBER BELT

ABSORBS DESTRUCTIVE HARMONICS, WHICH

CAN CAUSE SERIOUS PROBLEMS ON R ACING

ENGINES. SOME FEATURES INCLUDE A BILLET

ALUMINUM UPPER PULLEY WITH A HIGH TORQUE

DRIVE TOOTH CONFIGURATION, AN ALLOY STEEL

CRANK PULLEY AND GRADE 8 HARDWARE.

CHECK FOR COVER TO BLOCK INTERFERENCE AND

CORRECT IF PRESENT BY MODIFYING THE BLOCK.

IF YOUR BLOCK HAS BEEN LINE BORED, YOU

MAY ENCOUNTER A MISALIGNMENT BETWEEN

THE CRANK SEAL AND CRANK SNOUT. WE

RECOMMEND ENLARGING THE DOWEL PIN HOLES

IN THE COVER AND LOOSELY INSTALLING THE

COVER BOLTS BEFORE DRIVING ON THE LOWER

PULLEY. THIS PROCEDURE WILL INSURE THAT THE

CRANK SEAL IS CENTERED AROUND THE CRANK

SNOUT.

SECURE THE BELT DRIVE COVER TO THE BLOCK

USING AN OEM TYPE GASKET AND A THIN LAYER OF

RTV SEALER. TORQUE THE COVER BOLT 96 IN / LBS

(8 FT / LBS).

LUBRICATE AND SLIDE CAMSHAFT INTO BLOCK.

LOCATE THE REAR THRUST WASHER (WSH-39610

2.950” OD X 1.960” ID X .031”), CAM ADAPTOR

(ADP-30080) AND THREE 5/16-18 X 3/4” CAM

ADAPTOR BOLTS (BLT-31400).

Belt Drive Instruction Sheet

KBD - 32000, Mark 4 BB Chevrolet

KBD - 32200, Mark 5 BB Chevrolet

KBD - 32300, Gen 6 BB Chevrolet

INS - 32000

1 2 3 4

Summary of Contents

Page 1 - Belt Drive Instruction Sheet

APPLY A VERY THIN LAYER OF RTV SEALER TO THE RECESSED AREA ON THE CAM ADAPTOR.LUBRICATE AND INSTALL THE REAR THRUST WASHER ON THE CAM SNOUT. APPLY RTV

Page 2 - STEP 7

STEP 4 STEP 5 STEP 6 STEP 7APPLY A THIN FILM OF OIL TO THE OUTER BRONZE THRUST WASHER (WSH-39660 2.950” OD X 2.260” ID X .031”) AND INSTALL OVE

Page 3 - STEP 10

STEP 8 STEP 9 STEP 10STEP 11ROTATE CRANKSHAFT SO THAT #6 CYLINDER IS AT T.D.C.ROTATE THE CAMSHAFT SO THAT THE KEYWAY IS AT THE 12 O’CLOCK POSITIO

Page 4 - KIT CONTENTS:

1985 CEDAR BRIDGE AVESUITE 2 LAKEWOOD, NJ 08701732-901-1800, FAX 732-901-6777www.jesel.comTHIS INSTRUCTION SHEETS IS INTENDED AS REPRESENTATION ONLY.

Comments to this Manuals

No comments

Jesel INS-32000 Mark 4/5, Gen 6 BB Chevy User Manual

Browse online or download User Manual for For the car Jesel INS-32000 Mark 4/5, Gen 6 BB Chevy. Jesel INS-32000 Mark 4/5, Gen 6 BB Chevy User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Jesel INS-32000 Mark 4/5, Gen 6 BB Chevy