Jesel INS-36100 Donovan 800 / Dart Titan +1.000 Raised C User Manual download pdf

APPLY A THIN LAYER OF RTV SEALER TO THE RE-

CESSED AREA ON THE CAM ADAPTOR.

WITH YOUR CAMSHAFT ON A WORKBENCH,

LUBRICATE AND INSTALL THE REAR THRUST

WASHER ON THE CAM SNOUT. APPLY SEALANT

TO THE THREADS OF THE CAM ADAPTOR BOLTS

AND BOLT THE ADAPTOR TO THE CAMSHAFT.

TORQUE CAM ADAPTOR BOLTS TO 28-30 FT/LBS.

STEP 1

STEP 2

STEP 3

CAM BOLT IS

LH THREAD

JESEL’S BELT DRIVE SYSTEMS ARE THE MOST

ACCURATE AND DURABLE CAMSHAFT DRIVE

SYSTEM AVAILABLE AND ARE USED BY THE

COUNTRY’S TOP RACE TEAMS. A PATENTED

HIGH TORQUE BELT OPERATES WITHOUT

LUBRICATION AND SPINS WITH LESS FRICTION

THAN CHAINS OR GEAR DRIVE SYSTEMS. THE

RUBBER BELT ABSORBS DESTRUCTIVE

HA RMONICS, WHICH CAN CAUSE SERIOUS

PROBLEMS ON RACING ENGINES. SOME

FEATURES INCLUDE A BILLET ALUMINUM

UPPER PULLEY WITH A HIGH TORQUE DRIVE

TOOTH CONFIGURATION AND AN ALLOY STEEL

CRANK PULLEY WITH GRADE 8 HARDWARE.

CHECK FOR COVER TO BLOCK INTERFERENCE AND

CORRECT IF PRESENT BY MODIFYING THE BLOCK.

CHECK FOR WATER PUMP AND BALANCER

CLEARANCE AS WELL.

IF YOUR BLOCK HAS BEEN LINE BORED, YOU MAY

ENCOUNTER A MISALIGNMENT BETWEEN THE

CRANK SEAL AND CRANK SNOUT. WE RECOM-

MEND ENLARGING THE DOWEL PIN HOLES IN THE

COVER AND LOOSELY INSTALLING THE COVER

BOLTS BEFORE DRIVING ON THE LOWER PULLEY.

THIS PROCEDURE WILL INSURE THAT THE CRANK

SEAL IS CENTERED AROUND THE CRANK SNOUT.

SECURE THE BELT DRIVE COVER TO THE BLOCK.

TORQUE THE COVER BOLTS TO 12 FT / LBS.

LOCATE THE REAR THRUST WASHER (2.950”

OD X 1.960” ID X .031”), CAM ADAPTOR (ADP-

30080) CAM ADAPTOR BOLTS (5/16-18 X 3/4”)

AND SPANNER WRENCH.

Belt Drive Instruction Sheet

KBD - 36100, Donovan 800 / Dart Titan

+1.000” Raised Cam

INS-36100

Note: BB Chevrolet shown for illustration purposes.

1 2 3 4

Summary of Contents

Page 1 - INS-36100

APPLY A THIN LAYER OF RTV SEALER TO THE RE-CESSED AREA ON THE CAM ADAPTOR.WITH YOUR CAMSHAFT ON A WORKBENCH, LUBRICATE AND INSTALL THE REAR THRUST WAS

Page 2 - STEP 7

STEP 4 STEP 5 STEP 6 STEP 7 LUBRICATE AND CAREFULLY INSTALL CAM-SHAFT.APPLY A THIN FILM OF OIL TO THE OUTER BRONZE THRUST WASHER (2.950” OD

Page 3 - STEP 10

STEP 8 STEP 9 STEP 10ROTATE CRANKSHAFT SO THAT #1 CYLINDER IS AT T.D.C.ROTATE THE CAMSHAFT SO THAT THE KEYWAY IS AT THE 12 O’CLOCK POSITION.PLACE

Page 4 - KIT CONTENTS:

1985 CEDAR BRIDGE AVE. LAKEWOOD, NJ 08701732-901-1800, FAX 732-901-6777www.jesel.comTHESE INSTRUCTION SHEETS ARE INTENDED AS REPRESENTATIONS ONLY. JE

Comments to this Manuals

No comments

Jesel INS-36100 Donovan 800 / Dart Titan +1.000 Raised C User Manual

Browse online or download User Manual for For the car Jesel INS-36100 Donovan 800 / Dart Titan +1.000 Raised C. Jesel INS-36100 Donovan 800 / Dart Titan +1.000 Raised Cam User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Jesel INS-36100 Donovan 800 / Dart Titan +1.000 Raised C